EasyPIC v7 review
What’s new and what isn’t
In this article I will review the new EasyPIC v7 development board from Mikroelektronika. I will compare it to the previous version, will look at the new design, take you through what is on board and what is no longer there and finally give you a general overview of it.
I really do not believe Mikroelektronika needs any more publicity on the EasyPIC v7, but I felt it would be nice to go through reviewing the new board my way and most importantly compare it with its predecessors!
Now, I am not going to compare them since the beginning of time, also because I jumped on board of the EasyPIC wagon only as of version 5, but I think it is nice to visually analyse the evolution of the board across the various versions it went through. Quite an impressive progression really! The quality of photography too 🙂
The designers of these great boards will hopefully forgive me if the considerations in this section may sound quite superficial, but I would first of all just give simply a visual impression of the various layouts without going in the details of why from an engineering point of view things were placed here or there. So with this in mind this is what I see:
It is interesting to notice how the various elements did and did not move from board to board. The layout of the EasyPIC2, 3, 4, 5 and 6 did not really change too much overall especially when compared to Version 7 which is without doubt the exception.
Led and buttons have always been bottom left but not in version 7 in which they have been placed in the ports area on the right.
The chip sockets more or less had been kept in the centre. One thing of note is that the EasyPIC5 as well as v7 have enough space for my trusty 40 pin zif socket to fit in. The EasyPIC6 would not allow it because the switch above the socket was really too close.
|EasyPIC5, 6, 7 40 pin sockets side by side|
|EasyPIC v7 with zif socket|
|EasyPIC5 with zif socket|
The ports were top to bottom on the right, quite so in version 7 too but now you have two connectors and a proto header per port plus another connector per port on the left! No wonder, their theme for this version is connectivity!
The LCD spot of the EasyPIC 2 was taken by the GLCD in the EasyPICS 3,4,5 and 6 sending the LCD towards the top left area. I presume the GLCD was also the reason why the form factor as of the EasyPIC3 became bigger. Whereas the LCD is quite in the same place on version 7 too, the GLCD has taken the place of the buttons and led.
With regards to size wise apparently the boards are growing over time. The EasyPIC5 measured 25×21 cm, the EasyPIC 6 and v7 are both 26.5×22 cm.
The on-board programmer and the power section area made it to the version 7 keeping the same spot. Interestingly the on-board programmer has now a “warranty void if removed” shield. I am not sure I like it, even in the manual it is represented as a “black box”. Could this be for copyright?
The external communication connectors have also kept their space exception made for the serial port which as of version 6 is in the top left corner.
The 7 segment display was “less lucky” it travelled quite a bit and at one point it made it off the board entirely. Welcome back in v7!
Similar sort had the DS1820 which every time was really placed where there was space left.
The AD converter trimpots have remained pretty much where they were from version 2 to 5 and to 6 although in this version one was removed. In version 7 they have been moved together with the other two trimpots for the GLCD and LCD in a column next to the displays area.
A more rational design
As you can understand by now, version 7 was quite revolutionary in its design. It grouped elements in functional areas much more than any of the previous versions and sacrificed some gadgets that were introduced in version 6, towards usability and a rational layout.
The switches area is also all in one place, exception made for the new tristate port switches. I am sure this arrangement, along the lines of the grouping of displays and trimpots, will be much appreciated especially by beginners.
I haven’t used the new board too much yet but it looks to me that after a bit of readjusting my habits to the new layout it should be much easier to use. It shows some radical re-thinking of the board which must have taken some major effort and courage from Mikroelektronika. I am sure it will pay off.
Having port connectors to the left and to the right is really nice, you can now spread your work on each sides of the board. Often you have far too many things on the right of the board when you are working with complex projects and several accessory boards. Having port connectors on the left will surely help to have a much neater workbench.
What is and was on board
The new board comes with the usual PC keyboard, USB and serial port connectors and the Ext ICD provided as of version 6. A notable new addition is the new UART via USB based on the FT232RL chip. I would not be surprised to see the RS232 disappear from a future version 8 but I certainly hope it doesn’t. Dinosaurs like me grew to love it and might be difficult to part from the good old connector.
At the end of his EasyPIC6 review Roman makes a list which in part turns out spookley prophetic!
According to him the perfect board should have had amongst other things:
2 AD converter trimpots as in the past versions
A piezo buzzer
An I2C eeprom
… and as if by magic you find all of the above on the EasyPIC v7! I couldn’t agree more, those things were needed and are a welcome addition.
|EasyPIC v7 port group|
The only doubt I have here is whether the two port headers on the right were necessary at all times or if maybe a couple of EasyTEST would have been enough when needed.
With a workbench in mind and certainly for an educational setup, version 7 added four mounting holes to the corners of the boards. Nice touch!
Anybody who has done any measurements on the previous boards would certainly welcome the additional GNDs point, this is something I have personally been waiting for. Much appreciated indeed.
|EasyPIC5 DIY spacers|
|EasyPIC v7 plastic spacer|
Attention to details made so that as of the EasyPIC6 a couple of plastic display spacers were installed on the board. This was indeed a nice addition especially when using the touch screen for the GLCD without resorting to diy as I did for my EasyPIC5.
The dramatic redesign of the board came with some sacrifices and claimed some victims.
The menu and the 4×4 keypads, the port expander and the COG display had short life. Newly introduced in version 6 they have already disappeared. Let me attempt to guess why that was and how can one live without.
|Keypad 4×4 board|
With regards to the keypads I can see two possible reasons to why you really do not need to have them on board. The first is that an Keypad 4×4 Accessory Board is available if you really need to develop applications that need those keypads. Having it on board was probably not needed after all. The second is that UIs are shifting to touch screen and one could make use of the GLCD more and more instead of using the buttons. Either ways I don’t think too many people are going to be missing the two keypads too much.
|EasyPIC v7 with COG|
The COG has been removed in favour of the return of the 7 segment display. I must agree with Gavin from MCU Store here, the replacement had probably been triggered by the fact that educational establishment love teaching multiplexing and strobe of I/O lines. Roman made a good point with regards to using the COG as a debugging display when using the main LCD as the normal output of the application. Personally, when possible, I tend to use the serial port as a way to do debugging over a terminal, if anyway you feel you cannot do without the COG there is now an accessory board COG 2×16 LCD Board which brings it back on one of the many port headers available on the EasyPIC v7.
|EasyPIC6 Port Expander|
|Port Expander Board|
The other missing element is the port expander. I fully support the decision to remove them to make more space and rearrange the board in such a nice way. As for the previous elements there is a Port Expander Board and the new Expand Click that can be added should you need further connectivity to the one already provided!
I hope by now I have convinced EasyPIC6 owners to upgrade to v7. The new board has a few element less than the previous one but all there was can be added if needed. Some of the things added to the current version are unique to it and make so that the board is more professional, usable and expandable than each previous version ever was.
The EasyPIC v7
I bought my EasyPIC v7 from MCU Store which is the UK distributor for Mikroelektronica’s products and had a really nice and friendly chat with the owner Gavin, asking for his personal view on the new board in light of writing this article. He kindly provided a few good points, not a surprise giving his knowledge of this kind of products. Amongst his comments he pointed me to the EasyPIC6 review from Roman Black which I would really invite you to read and was an excellent source of material for this review.
The EasyPIC6 introduced the SMD technology which contributed to a neater and more compact design. With the EasyPIC v7 this is taken to a further level. Click Boards are all SMD and through hole technology is gradually disappearing from the rest of the more traditional accessory boards.
How does it feel?
The board is build to last and gives the impression of being quite sturdy in general, the buttons feel nice to the touch, they make a clicking noise when pressed and are to me of better quality than in previous version. With regards to buttons, the reset has been moved to the top right corner of the board far away from other buttons and in my opinion in a better position to avoid pressing it accidentally.
|EasyPIC v7 tristate switch|
The new tristate switches allow for pull-up/down or disable for each pin. Disable a single pin was not possible before. I find them a bit too small and fiddly to use with just the fingers which I could with the previous version of dip switches, you will probably need a pen or some tool to set them. On the contrary of what I thought it is pretty easy to put them in the middle position. Overall however the previous type of switch, which is still used for the configuration of the board, felt better to use.
I had to send back the first board I received because one of the trimpot knobs was broken, which can happen, but most annoyingly the LCD one was really quite loose and when measured it turned out to be faulty. The values on the ohmmeter where jumping all over the place when adjusting the resistance.The new board I received is fine but the trimpots still feel quite loose, maybe it is just a bad batch and hopefully the majority of the boards will be fine.
|EasyPIC v7 dip switch|
The LCD and the GLCD have not changed, the backlight though has and it is now possible to choose between Standard or PWM driven!
The documentation provided is, as always, of really good quality. Incredibly detailed and really easy to go through. For those who are not familiar with the board they would be able to get up to speed with it in no time.
In writing this review I have noticed however that for this version of the board there are practically no high resolution pictures like there were for the EasyPIC5. I think it is a shame it is no longer available and hope Mikroelektronika might reconsider adding it again.
The schematic is absolutely excellent, I would really love if it were printed on a single page to “plaster” on the wall and keep as constant reference.
The package also includes a CD with all the software needed for you to start working with the board. To be in line with the excellent material provided in the box, all the software present on the CD I have received was up to date.
Some of the new aspects of the EasyPIC v7 have already been listed above, a radical new design, new components and the connectivity theme. Three of the most important new entries are however the 18F45K22, the dual power supply and the mikroBUS.
The 18F family
The dual power supply
The EasyPIC6 changed the power supply from a 7805 voltage regulator type to a switching one. On my EasyPIC5 I had to add a heatsink to reduce the temperature of the voltage regulator, reading Roman’s article I realise it probably was common practice. The new switching power supply meant this problem was gone and that the range of input voltages had also increased as shown in the table below.
With the EasyPIC v7 the power supply section has been further improved. There is now an additional crew terminal connector but most importantly you can now choose between 5v and 3.3v output voltages increasing the number of supported microcontrollers.
Mikroelektronika is putting quite some energy in promoting this new bus, many new Click boards compatible with this novel “plug and play” connector.
|EasyPIC v7 mikroBUS|
I think Mikroelektroinka has done overall an excellent job with the EasyPIC v7 in delivering a mature product, strong of many years of experience and of a large community continuously contributing to improve the board and its software platform.
The quality of the build is indeed very good, the attention to details and the look and feel are excellent.
Some things have left the board from the previous version, some have returned from the past, however the EasyPIC v7 is not simply an upgrade from previous versions instead its designers have managed to bravely approach a new layout which makes version 7 a complete shift towards a truly professional development board.